Voron tap guide

INSTALL ONTO VORON STEALTHBURNER WWW.CHAOTICLAB.XYZ 06 INSTALL ONTO VORON STEALTHBURNER WWW.CHAOTICLAB.XYZ PRESS TOOLHEAD ONTO TAP After inserting the tool head assembly into the 3mm gap left by the two M3x12 screws mentioned on page 05, please press the toolhead along the direction indicated by the blue arrow in the figure until the back of the tool head is completely attached to the TAP.

NOTE Because CNC machining is more precise than printed parts riveting copper nuts, if the tool head assembly is not installed in place, it will cause the subsequent screws to be unable to lock in. Bed motion compromises the accuracy of CNC VORON TAP V2, so it is not recommended for Voron 1.8, Legacy, or Switchwire designs. Heat Set Insert Installation

1. Install the 11 required M3 heat set inserts into the Tap center component
2. Use a soldering iron set to approximately 260°C
3. Press each insert straight down until flush with the plastic surface
4. Allow inserts to cool completely before moving to the next step

Sources: ,

3.

When the probe is stowed it will be pulled high by the internal probe circuit and the internal MCU pull up. Magnet Installation

1. Apply a small amount of CA glue to each magnet recess
2. Insert the 6mm × 3mm magnets with proper polarity
3. For the pairs of magnets that will interact, ensure opposite polarities face each other
4. Hold each magnet in place until the glue sets
5. Wipe away any excess glue before it dries

Note: Correct magnet polarity is critical for proper operation.

ATTENTION WWW.CHAOTICLAB.XYZ Highlighted in blue are included in this CNC VORON TAP V2 Highlighted in red are other accessories of the Voron printers, which are not included in this CNC VORON TAP V2 and will need to be prepared by yourself. Configure the pin to be internally pulled up. If there is a wire break then the signal will continue to indicate that the probe is stowed and it becomes possible for the probe to crash into the bed.

FOLLOW THE STEPS BELOW TO GREASE YOUR RAIL WITHOUT DISASSEMBLY: 1. Thread the M3 x 12 SHCS directly into the CNC part, but do not tighten fully. BED MOUNT MUST BE SECURE When CNC VORON TAP V2 is probing, the nozzle will contact the bed with a force of approximately 500-800 grams. Main Tap Mechanism Assembly

1. Attach the Tap center component to the MGN9 carriage using M3 screws
2. Install the required springs and guide pins
3. Verify that the mechanism moves freely and returns to position
4. Add the necessary washers and M3 nuts as specified in the manual

5.

Drop a few drops of isopropyl alcohol down the rail on either side to flush out the WD-40 degreaser. The forum is another excellent source of Voron help and advice.

VoronDesign.com - If you are not purchasing a kit, the BOM and sourcing tools found here will be an important part of your build

Github - All Voron designs are Open Source.

Spray your lubricant on either side of the rail liberally and run the block up and down the rail repeatedly to allow the lubricant to reach all of the balls within the block. Configure the 'SERVO' pin to be pulled down in software. Yes.

(Bonus Points) Data Science

Tap engineering is backed by data science. Therefore, before proceeding to the next step, please check whether the tool head assembly is already installed in place as shown in the figure.

03 INSTALL TO MGN12H WWW.CHAOTICLAB.XYZ SCREWS FOR MGN12H The CNC Voron TAP V2 comes pre-installed with four screws for mounting to the MGN12H rail. The spec configurations have been tested extensively and are well supported.

---

• Discord - The Discord server is the heart of the Voron community, you can find information and advice about almost anything here.

• Forum - The chaos of Discord isn’t for you?

  ZH1.50-3PIN ≥70mm CONNECTION METHODS WWW.CHAOTICLAB.XYZ There are two possible ways to connect the CNC VORON TAP V2. Both ways will provide a signal that indicates when the probe is triggered or not triggered but one way will also offer protection against the probe crashing into the bed in case of an accidental wire break.